What is electrical troubleshooting?
Electrical troubleshooting is finding the actual cause of a fault and fixing that cause, instead of replacing parts until the symptom goes away. For most homeowners it starts with one of three things: lights that flicker or dim, a breaker that keeps tripping, or an outlet that has stopped working.
The method is the same every time. The electrician tests the circuit, its connections and the devices on it, narrows the problem to one spot, and explains what was found before any repair begins. If it is urgent, the 24/7 emergency electrician page covers what to do right now.
Why do my lights flicker or dim?
Flickering has a short list of causes. The simple ones are a worn or loose bulb, a dimmer that does not suit the bulbs on it (common with LED bulbs), or a switch that is wearing out. The more serious ones are a loose connection in a fixture, a junction box or the panel, an overloaded circuit, or a problem with the service coming into the home.
Where and when it happens tells you a lot. One fixture usually points to that bulb, switch or fixture. Lights that dim when the air conditioner or another large appliance starts point to the load on the circuit or the service. Flickering in several rooms, or flickering with a buzz or a burning smell, is worth a call right away, because a loose connection can heat up. The Electrical Safety Foundation International lists flickering and dimming lights among the warning signs of an overloaded circuit or a wiring problem.
Why does my breaker keep tripping?
A breaker trips to stop a fault, so a trip is information, not just a nuisance. There are three common reasons, plus a worn breaker:
- Overload. Too much is running on one circuit. A 15-amp, 120-volt circuit carries about 1,800 watts at most (15 amps times 120 volts), or about 1,440 for loads that run three hours or more. A 20-amp circuit carries about 2,400 watts at most, or about 1,920 for loads that run three hours or more. A space heater and a hair dryer on the same circuit can pass the limit.
- Short circuit. A hot wire touches a neutral or another hot wire. The breaker trips at once, often with a pop.
- Ground fault. Current leaks to ground, often through a damaged wire or a wet appliance or fixture.
- A worn breaker. Breakers wear out and can trip below their rating.
The size of the breaker is matched to the wire behind it. Under the National Electrical Code, standard copper house wiring is limited to a 15-amp breaker for 14-gauge wire, 20 amps for 12-gauge and 30 amps for 10-gauge (Section 240.4(D)). That is why a bigger breaker is never the fix: it lets the wire carry more current than it can take. If a breaker trips again right after you reset it, or trips with nothing running, leave it off and call.
Why is my outlet or switch dead?
Before assuming the outlet itself is bad, look at what else is on the circuit. The usual causes are:
- A tripped breaker.
- A tripped GFCI outlet somewhere else on the circuit. One GFCI outlet in a bathroom, kitchen, garage or outdoors can protect other outlets downstream.
- A loose or burned connection behind the wall or in the device.
- A failed outlet or switch.
- An outlet that a wall switch controls, which is common in living rooms and bedrooms.
The U.S. Consumer Product Safety Commission recommends testing every GFCI once a month: plug in a light, press the test button and the light should go out, then press reset and it should come back on. If it does not, the GFCI needs to be replaced. The same checklist warns that unusually warm outlets or switches may mean an unsafe wiring condition, such as a loose connection that can start a fire. Some dimmers warm up normally. A warm or discolored outlet is one to stop using until an electrician looks at it. When the outlet or switch itself is the problem, or you want a GFCI, a tamper-resistant outlet or a new switch while the box is open, see outlets and switches.
When is it an emergency instead?
A burning smell, sparking, a hot or buzzing panel, scorch marks or a shock is urgent, not something to schedule for next week. Turn off the affected circuit if you can do it safely, keep people away from the area and call (561) 777-9982, which is answered 24/7. If there is smoke or fire, call 911 first.
Less dramatic signs still count. Breakers that trip repeatedly, lights that dim when the AC starts and outlets that work only sometimes point to a fault that tends to get worse, not better. If the same fault keeps coming back in an older home, an inspection and rewiring visit may be the better fix.
What can I safely check myself?
Some checks are safe for anyone, and they make the visit faster:
- Note what happens, where it happens and when it started or last worked.
- Unplug what is on the affected circuit, then reset the breaker once. Do not keep resetting it.
- Press reset on any GFCI outlets nearby, and swap in a new bulb or try a different switch.
- Check whether a wall switch controls the outlet.
Leave the panel cover and the wiring to an electrician. The wires coming in from the utility stay energized even with the main breaker off. If a panel upgrade turns out to be the real answer, the troubleshooting visit will show it, and surge protection is worth a look if storms keep taking out equipment.
Who does electrical troubleshooting in Palm Beach County?
K&J Electrical Solutions does. We are a family-owned, owner-operated electrician in Palm Beach County, run by Jake and Kevin, and the two of them do the work themselves. You describe the problem, we test the circuit, and you hear what we found before any repair starts. We work across the county, including West Palm Beach, Boynton Beach, Delray Beach, Boca Raton, Lake Worth Beach and Wellington. Our phone is answered 24/7 at (561) 777-9982, and it takes texts too, or you can request an estimate.
Sources
- National Fire Protection Association, NFPA 70, National Electrical Code (overcurrent protection of conductors, Section 240.4(D); branch-circuit loading, Sections 210.19 and 210.20; arc-fault protection, Section 210.12): nfpa.org
- EC&M, The Apprentice’s Guide to AFCIs and the NEC, January 31, 2025: ecmweb.com
- U.S. Consumer Product Safety Commission, Home Electrical Safety Checklist, Pub 513, July 2008: cpsc.gov
- Electrical Safety Foundation International, Don’t Overload Your Home (warning signs of an overloaded circuit): esfi.org
- Electrical Safety Foundation International, Indoor Electrical Safety Check booklet (what an outlet GFCI protects, monthly testing): esfi.org
