What does electrical work on a new home include?
On a new home the electrician builds the whole electrical system from the ground up: the panel, the circuits to every room, the wiring for large loads like air conditioning, and the devices and fixtures at the end. K&J Electrical Solutions wires custom homes in Palm Beach County from rough-in to final trim.
It is done in stages because the walls are built in stages. Each stage has to be finished, and usually inspected, before the next trade can close it up.
What happens at rough-in and at final trim?
Rough-in comes after framing and before insulation and drywall. The panel location is set, boxes are fastened in place and cable is run to every outlet, switch, light and appliance. The rough-in is inspected before the walls are closed, because after that nobody can see the wiring.
Trim, or final, comes after drywall and paint. The switches, outlets, cover plates, fixtures and fans go in, the panel is finished and labeled, the circuits are tested, and the final inspection is passed before the power is brought up for good.
How is the electrical service sized for a custom home?
A load calculation decides it. The National Electrical Code, in Article 220, sets out how to add up what the home will run: air conditioning, which runs most of the year in Palm Beach County, plus the kitchen, water heating, laundry and every other large load. A larger home with more than one AC system, a pool and an EV charger adds up to more than a small one, and the calculation shows how much more.
That is also why the plan should name the extras early. If a panel upgrade would be needed later because the original panel was sized without them, it is simpler to size the panel for them now.
What should I plan for before the walls close?
Anything you might want in the next few years, because wiring is cheapest to add while the framing is open:
- An EV charger circuit near the garage or driveway, and the panel space for it.
- A generator inlet or transfer switch, with room in the panel.
- Pool equipment, which needs its own circuits (see pool electrical).
- Outdoor, landscape and ceiling fan or recessed lighting, including fan-rated boxes where fans will hang.
- Smart-home controls, which often need a neutral wire at the switches and a place for sensors.
If you are not sure what you will want, say so during the walkthrough. A few extra boxes or a conduit run are simple to add before drywall and much harder after.
Which electrical inspections does a new home need?
Inspections follow the stages of the build. Palm Beach County’s Building Division, which permits and inspects work in the unincorporated areas, lists these electrical inspections: temporary power, underground electric, rough electric, a hot check for single-family homes, and the final electric. Many cities, including West Palm Beach, Boca Raton, Jupiter and Boynton Beach, run their own building departments (see our generator permit guide), so the inspection sequence can differ.
The inspector also looks at protection devices. The National Electrical Code requires GFCI protection in places such as kitchens, bathrooms, garages and outdoors, and arc-fault (AFCI) protection for most living areas of a new home. Both are checked as part of the inspection.
Who wires custom homes in Palm Beach County?
K&J Electrical Solutions does. We are a family-owned, owner-operated electrician in Palm Beach County, run by Jake and Kevin, and the two of them do the work themselves. If you are planning a build, call or text while the plans can still change, because panel and switch locations are easiest to settle on paper. We work across the county, including Jupiter, Palm Beach Gardens, Boca Raton, Wellington, Royal Palm Beach and Palm Beach. Our phone is answered 24/7 at (561) 777-9982, and it takes texts too, or you can request an estimate.
Sources
- Palm Beach County Planning, Zoning and Building, Building Division inspection codes (electrical inspections: temporary power, underground electric, rough electric, hot check for single-family homes, final electric): discover.pbc.gov
- National Fire Protection Association, NFPA 70, National Electrical Code (load calculations, Article 220; GFCI protection, Section 210.8; arc-fault protection, Section 210.12): nfpa.org
- EC&M, The Apprentice’s Guide to AFCIs and the NEC, January 31, 2025 (rooms covered by arc-fault protection): ecmweb.com
- U.S. Consumer Product Safety Commission, Home Electrical Safety Checklist, Pub 513, July 2008 (GFCIs recommended in kitchens, bathrooms and other higher-risk areas): cpsc.gov
