Skip to content

Pool Electrical in Palm Beach County

K&J Electrical Solutions handles pool electrical work across Palm Beach County, including pumps, heaters, bonding, GFCI protection and pool-area lighting. Pools have their own section of the National Electrical Code, Article 680, because water and electricity share the space. Family-owned and owner-operated, phone answered 24/7 at (561) 777-9982.

License EC13016308 Answered 24/7

What's Included

Every pool electrical job covers these 7 points, done by Jake or Kevin themselves.

  • Pool pump circuits and connections, with GFCI protection
  • Pool heater circuits and connections, with a disconnect where the code calls for one
  • Bonding of the pool equipment and metal parts, and checks of existing bonding connections
  • GFCI protection for the pump, the outlets around the pool and the lighting, where the code requires it
  • Pool-area lighting wired to the pool rules in Article 680
  • A look at the panel to confirm it has room for the pump and heater
  • Permit and inspection where required

Signs You Need It

If you notice any of these, it is time to call about pool electrical.

  • A GFCI breaker or outlet at the pool equipment keeps tripping
  • The pump hums, will not start or trips its breaker
  • You feel a tingle or a shock near the pool or from pool equipment
  • Pool-area lights are out or flicker
  • Wiring, disconnects or bonding connections at the equipment look corroded
  • You are adding or replacing a pump, a heater or the lighting
  • Pool equipment failed after lightning or a storm

Ready to talk about pool electrical? You'll deal with Jake or Kevin directly.

What counts as pool electrical work?

Pool electrical work is the wiring in and around a pool: the circuits that feed the pump and heater, the disconnect near the equipment, the bonding wires that tie the pool’s metal parts together, the GFCI protection on those circuits and on nearby outlets, and the lights around the pool. K&J Electrical Solutions handles pumps, heaters, bonding, GFCI and pool-area lighting for homes across Palm Beach County.

Why does a pool have its own electrical rules?

A pool puts water, bare feet and metal parts in the same place, so a small electrical fault can matter far more there than in a living room. The National Electrical Code gives pools their own section, Article 680, and the Florida Building Code requires pool wiring, bonding and grounding to meet it.

Article 680 covers where outlets and lights may go, how circuits are protected, how equipment is disconnected and how metal parts are bonded. The edition your city or the county enforces decides the exact wording, so work on a pool is built to the rules in force where the pool is.

What is pool bonding?

Bonding is a network of copper conductors that connects the pool’s metal parts so they all sit at the same voltage. Section 680.26 of the National Electrical Code says its purpose is to reduce voltage gradients in the pool area, and it applies to pools with or without electrical equipment. The parts it covers include a conductive pool shell, the surfaces around the pool, metal components and fittings, underwater lighting, electrical equipment and fixed metal parts. They are joined with solid copper conductor not smaller than 8 AWG.

Bonding is not the same as grounding, and it does not replace it. Pool equipment is bonded and also connected to the equipment grounding conductor. Salt air and constant moisture are hard on metal connections, so bonding and equipment connections on an older pool are worth checking.

Where does a pool need GFCI protection?

A ground-fault circuit interrupter (GFCI) cuts the power when current leaks to ground, which is the shock path at a pool. The National Electrical Code calls for it in several places around a pool:

  • Pool pump motors. Outlets that supply pool pump motors on circuits up to 60 amps need GFCI protection, and a replacement pump motor must be given the same protection.
  • Outlets near the pool. Receptacles within 20 feet of the pool’s inside walls need GFCI protection, and other receptacles must be at least 6 feet from the inside walls.
  • Lighting. The Florida Building Code also requires GFCI protection for underwater lights that run above the low-voltage limit.

Section numbers and details shift from one code edition to the next, so the edition your building department has adopted is the one that counts. Test GFCI protection regularly too. The U.S. Consumer Product Safety Commission recommends testing every GFCI once a month.

What about pool pumps, heaters and lighting?

Pumps. A pump needs a circuit sized for its motor, GFCI protection and a disconnect within sight of the equipment. When a pump is replaced, the GFCI protection is part of the job.

Heaters. A pool heater is a large electrical load. Whether your panel has room for it comes down to a load calculation, which is the same reason pool equipment is a common cause of panel upgrades.

Disconnects. Article 680 requires a maintenance disconnect for pool equipment other than lighting. It must be readily accessible and within sight of the equipment, and generally at least 5 feet from the pool’s inside walls.

Lighting. Lights near the pool have their own rules, including that the transformers and power supplies that feed pool lighting must be listed for pool use. For landscape and patio lighting around the pool, see lighting.

Why do pool electrical problems show up in Florida?

Three things work against pool equipment here. Salt air near the ocean and the Intracoastal corrodes disconnects, fittings and connections. Lightning and grid surges damage pool controls and motors, and a panel-mounted surge protector helps guard against them. And storms and flooding put equipment under water.

After a storm or flood, do not switch power back on to anything that got wet, including pool equipment, until an electrician has checked it. For urgent problems, see 24/7 emergency repair or call right away.

What should I do if I feel a tingle near the pool?

Treat it as urgent. Get everyone out of the water and keep them out until the problem is found. If you can reach the pool equipment breaker or the main breaker without standing in water, switch it off. Then call (561) 777-9982, which is answered 24/7. A tingle or a shock near a pool can mean a fault in the equipment, the wiring or the bonding, and it is not something to test by swimming. Do not enter the water to help someone being shocked. Cut the power if you can and call 911, which comes first if anyone is hurt.

Who does pool electrical work in Palm Beach County?

K&J Electrical Solutions does. We are a family-owned, owner-operated electrician in Palm Beach County, run by Jake and Kevin, and the two of them do the work themselves. We handle pumps, heaters, bonding, GFCI and pool-area lighting, and you deal with the owners from the first call to the final test. We work across the county, including Boca Raton, Wellington, Jupiter, Palm Beach Gardens, Royal Palm Beach and Delray Beach. Our phone is answered 24/7 at (561) 777-9982, and it takes texts too, or you can request an estimate.

Sources

  • National Fire Protection Association, NFPA 70, National Electrical Code, Article 680, Swimming Pools, Fountains, and Similar Installations: nfpa.org
  • Florida Building Commission course material, Swimming Pool Safety (FBC course 962.1), quoting NEC Sections 680.13, 680.21, 680.22 and 680.26 and Florida Building Code, Building, Section 454.2.16: floridabuilding.org
  • EC&M, Keeping Pools and Spas Safe, April 13, 2022 (based on the 2020 NEC): ecmweb.com
  • U.S. Consumer Product Safety Commission, Home Electrical Safety Checklist, Pub 513, July 2008: cpsc.gov

Pool Electrical Questions

What is pool bonding, and why does it matter?

Pool bonding ties the pool's metal parts and equipment together with copper conductors so they stay at the same voltage. The National Electrical Code (Section 680.26) requires it to reduce voltage gradients in the pool area, using solid copper not smaller than 8 AWG. Bonding works alongside grounding, not instead of it.

Does my pool pump need GFCI protection?

Yes. The National Electrical Code requires GFCI protection for the outlets that supply pool pump motors, and requires it again when a pump motor is replaced. The Florida Building Code has a similar rule for pool pump circuits. K&J Electrical Solutions checks the GFCI protection whenever it works on a pool pump circuit.

How close can an outlet be to the pool?

Under Article 680 of the National Electrical Code, receptacles for loads other than the pool's circulation system must be at least 6 feet from the pool's inside walls, and receptacles within 20 feet of the inside walls need GFCI protection. Details change between code editions, so your building department's adopted edition decides.

Does pool equipment need its own disconnect?

Yes. Article 680 calls for a maintenance disconnect for pool equipment other than lighting. It has to be readily accessible and within sight of the equipment, and generally at least 5 feet from the pool's inside walls unless a permanent barrier separates it from the water.

Do I need a permit for pool electrical work in Palm Beach County?

In most Florida cities and counties, new circuits and equipment connections are typically permitted and inspected through the local building department. The Florida Building Code requires pool wiring, bonding and grounding to meet the National Electrical Code. K&J Electrical Solutions pulls the permit where one is required.

What should I do if I feel a tingle in the pool?

Treat it as urgent. Get everyone out of the water and keep them out. If you can switch off the pool equipment breaker or the main breaker without standing in water, do it. Then call (561) 777-9982, which is answered 24/7. Do not enter the water to help someone being shocked. Cut the power if you can and call 911.

Still have a question? Ask the owners directly.

Need help right now?

Call or text (561) 777-9982. We answer 24/7, and you get Jake or Kevin, not a call center.

Power out, burning smell, sparking outlet or a breaker that won't reset? Call now.

Not urgent? Request a free estimate.

We typically reply within one business hour.

* Required. We only use your details to answer your request.

Other ways to reach us

K&J Electrical Solutions logo

K&J Electrical SolutionsBoynton Beach, FL

Open our Facebook page Recommend us on Nextdoor
Address
K&J Electrical Solutions
9377 Longmeadow Cir, Boynton Beach, FL 33436
Service area
Palm Beach County, FL
License
Licensed and insured Florida electrical contractor EC13016308
K&J Electrical Solutions logo

We Answer 24/7

Need an electrician? Jake or Kevin picks up, day or night.

Emergency service
24/7, every day
Service area
Palm Beach County
FL license
EC13016308
Call (561) 777-9982